Psvane Treasure Mark II 6CA7-T/EL34

PSVANE Treasure Mark II 6CA7-T/EL34

Psvane Treasure Mark II 6CA7-T/EL34

Psvane Treasure Mark II 6CA7-T/EL34

Psvane Treasure Mark II 6CA7-T/EL34

Psvane Treasure Mark II 6CA7-T/EL34

Psvane Treasure Mark II 6CA7-T/EL34

Psvane Treasure Mark II 6CA7-T/EL34

    • Crystallized carbon grey coating inside the tube: This makes the TII series tubes to be a ‘grey bottle’, not a ‘black bottle’. The Crystallized carbon coating technology used in vacuum tubes have been patented by Psvane Audio in China and pending abroad. The benefit of the Crystallized Carbon coating will improve on absorbing random electrons inside the vacuum tube and dissipating heat more efficiently under extreme temperature, which will further enhance the stability of the vacuum tubes.

      Teflon Base with Oxidized Aluminum Collar: instead of using fragile ceramic base, the TII series tubes use low conductance and highly durable Teflon materials for the base (no including the guide pin in the middle) to improve on anti-corrosion and anti-breakage. The brass-color sandy Oxidized aluminum collar around the Teflon base is anti-corrosion as well – no more finger prints and oxidization on the tube base with time of use, and your tubes will maintain a prestige condition for a long time.

      Product logo engraved on the base, not printed on the glass enclosure: As many tube amps have tube sockets installed in various directions based on circuit layout, previously the printed logo on the black bottle tubes may face inconsistent directions. TII series have logo only engraved on the base so your amp will maintain a consistent and highly desirable appearance for all TII series tubes.

      Higher quality glass enclosure: Higher quality glass is used for the new TII series to offer a better hand feel of the tubes, plus slightly heavier weight (approx 10% among all models) than previous series.

      Last but not least – Sound Quality not a tiny bit less: TII series offers not a tiny bit less sound quality than the previous T-series. The new coating materials offer an even better music presentation in terms of minor 3D imaging improvement, layering and clarity. You will not lose anything in terms of sound by going for the latest and newest TII series if T-series are phased out and will gain all the greatly improved workmanship mentioned above.

6CA7-TII is high property audio output pentode, its anode limited dissipation power is 25W, the output power is over 10W when it is used as class A1 in amplifier single tube, and it is over 35W when it is used as class AB1 double tubes.
6CA7-TII is very similar with EL34, which can be replaced by each other.

Heater
UH……………………………6.3 V
IH……………………………1.5 A
Static Parameter
Ua…………………………… 250 V
Ug2……………………………250 V
Ug3…………………………… 0 V
-Ug1…………………………12.2 V
Ia…………………………… 100 mA
Gm…………………………… 11 mA/V
ri…………………………… 15 kΩ
μg1-g2………………………11
Maximum Rating
Ua……………………… 800 V
Ug2………………… 500 V
Ug1………………… -100 V
Pa………………… 25 W
Pg2…………… 8 W
Ik………………………150 mA
Rg1
With cathode bias………………………0.7 MΩ
With fixed bias……………………0.5 MΩ
Uh-k ………………±100 V
Tbulb………………………250 ℃
Direct Interelectrode Capacitances
input…………………… 15.2 PF
output…………………… 8.4 PF
grid to plate…………………… 1.1 PF
grid to filament……… 1.0 PF
Cathode to filament…………… 10 PF
Recommended Operating Conditions(reference value)
class A1, singel tube, fixed bias
Ua(b) …………………… 265 265 V
Ua……………………………250 250 V
Ug2……………………… Rg2=2k Rg2=0
Ug3……………………………0 0 V
-Ug1……………………… 14.5 13.5 V
Ia(0) ………………………70 100 mA
Ig2(0) …………………… 10 14.9 mA
Gm…………………………… 9 11 mA/V
ri……………………………18 15 kΩ
RL…………………………… 3 2 kΩ
Pout………………………… 8 11 W
Dtot…………………………10 10 %
push-pull, class B1, fixed bias
Ua……………………………375 400 V
▲Rg2………………………… 600 800 Ω
Ug3………………………… 0 0 V
-Ug1………………………… 33 36 V
Ia(0) …………………2×30 2×30 mA
Ia(maxsig) ………2×107.5 2×110.5 mA
Ig2(0) ………………2×4.7 2×4.5 mA
Ig2(maxsig) ………2×23.5 2×23 mA
Rl(a-a) ………………3.5 3.5 kΩ
ü(g1-g1)(r.M.S) ……… 46.7 50 V
Pout……………………48 54 W
Dtot……………………2.8 1.6 %
▲ Rg2is used in two tubes.
push-pull, classB1, cathode bias, ultra-linear connection
(43% tapping points)
Ua………………………………430 V
Rg2…………………………… 2×1 kΩ
Ia(0) ………………………2×62.5 mA
Ia(max.sig) ……………… 2×65 mA
Ig2(0) ………………………2×10 mA
Ig2(max.sig) …………… 2×10.2 mA
Rk……………………………2×470 Ω
?(g1-g1)(r.M.S) ……………35 V
RL(a-a) ……………………… 6 kΩ
Pout……………………………20 W
Dtot………………………… 0.35 %

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>